Badger short stoke hammer/trigger

Forum for the discussion of SCCY CPX-1 & CPX-2 compact 9mm and CPX-3 subcompact .380 ACP pistol modifications, holsters, and other after-market items.

Badger short stoke hammer/trigger

Postby usmale » Wed Jan 03, 2018 6:19 pm

Bought from Galloway a Badger short stoke hammer/trigger combo, installed, it takes out about 50% of the trigger pull, same poundage, makes the Sccy Cpx 2 a
Beast! You can adjust take up and post travel, shot 250 rds no problems

Image
Sccy CPX2 two-tone #066XXX EDC
NRA Life Member
Glock Armour
User avatar
usmale
Forum Regular
 
Posts: 56
Joined: Sun Jun 26, 2011 8:55 pm
Location: Morrow, Ohio

Re: Badger short stoke hammer/trigger

Postby HootmonSccy » Wed Jan 03, 2018 9:22 pm

It doesn't look like a very good shape for the trigger, but maybe it's just the picture..
How much for the set up, and does it come with instructions?
Image
"They who can give up essential liberty to obtain a little temporary safety, deserve neither liberty nor safety."
Ben Franklin
"I prefer dangerous freedom over peaceful slavery." - Thomas Jefferson
User avatar
HootmonSccy
Topic Moderator
 
Posts: 2306
Joined: Wed Aug 26, 2009 10:42 am
Location: Tampa Bay, Florida

Re: Badger short stoke hammer/trigger

Postby usmale » Wed Jan 03, 2018 9:44 pm

No instructions, but Galloway has a YouTube video, took about 20 mins to replace the hammer and trigger,,,,,, trigger reminds me of an Apex for a Glock,, flat faced bad picture through
Sccy CPX2 two-tone #066XXX EDC
NRA Life Member
Glock Armour
User avatar
usmale
Forum Regular
 
Posts: 56
Joined: Sun Jun 26, 2011 8:55 pm
Location: Morrow, Ohio

Re: Badger short stoke hammer/trigger

Postby usmale » Wed Jan 03, 2018 9:45 pm

Sccy CPX2 two-tone #066XXX EDC
NRA Life Member
Glock Armour
User avatar
usmale
Forum Regular
 
Posts: 56
Joined: Sun Jun 26, 2011 8:55 pm
Location: Morrow, Ohio

Re: Badger short stoke hammer/trigger

Postby Lefty Red » Thu Jan 04, 2018 5:54 am

Have used their products for a Kimber Micro 9.
The trigger look weird but the flat face makes for good shooting.

Sent from my Pixel 2 using Tapatalk
Last edited by Lefty Red on Fri Jan 05, 2018 3:13 am, edited 1 time in total.
User avatar
Lefty Red
Seasoned Member
 
Posts: 107
Joined: Tue Jan 17, 2017 9:54 pm

Re: Badger short stoke hammer/trigger

Postby wrench459 » Thu Jan 04, 2018 8:37 pm

First off I'm in no way connected to Galloway.
I first got the Badger trigger installed it then went to the range.
I really like the trigger.

A few weeks later I got the hammer .
Not been able to test it out at the range yet (ambient temp to low for my old bones).
I've got mixed feelings with the hammer. I'll save my judgment until I get to the range again.
Image
wrench459
Veteran Member
 
Posts: 391
Joined: Sat Dec 05, 2015 6:37 pm

Re: Badger short stoke hammer/trigger

Postby Joe C » Thu Feb 01, 2018 10:07 am

I too added the Badger trigger kit in my CPX 2,as I liked the sound of a shorter trigger travel. I also thought about their reduced strength hammer spring. I emailed them and they said if I was putting the Badger kit in they would not recommend adding the reduced spring as their might be soft hits on some types of ammo.

I'm new here so I will try adding some photos but not sure if it will work. Here's my CPX with the kit installed,

https://s26.postimg.org/ip7m4xaa1/IMG_0506.jpg

Before I converted it I shot 200 rounds through it and then put up a target and shot 30 rounds through it. I feel shooting a couple hundred rounds first gives me a better sense of how it will perform.

https://s26.postimg.org/ktrz6046x/IMG_0509.jpg

Here is the after the kit was installed, same routine as to number of rounds. Not really much different but the trigger pull was much better.

https://s26.postimg.org/pfo3ed55l/IMG_0512.jpg

Would I recommend this kit for anyone? Not really, I do like the shorter trigger travel but probably not enough to say it is necessary on a carry pistol. In a situation where I need to use it, adrenaline and focus on the situation would probably negate the difference.
Failure is not an option
Joe C
New Member
 
Posts: 6
Joined: Tue Jan 30, 2018 8:37 pm

Re: Badger short stoke hammer/trigger

Postby HootmonSccy » Thu Feb 01, 2018 5:19 pm

Joe C -
You picture links work fine, but next time If you look below the text box there is an "Upload Attachment" tab..
You can add photos there. Instead of links, it will look like this...
Attachments
RM380_VS_CP2.jpg
Image
"They who can give up essential liberty to obtain a little temporary safety, deserve neither liberty nor safety."
Ben Franklin
"I prefer dangerous freedom over peaceful slavery." - Thomas Jefferson
User avatar
HootmonSccy
Topic Moderator
 
Posts: 2306
Joined: Wed Aug 26, 2009 10:42 am
Location: Tampa Bay, Florida

Re: Badger short stoke hammer/trigger

Postby Joe C » Thu Feb 01, 2018 9:59 pm

Thanks for the info. There is always a learning curve when one is new at navigating a site. I'll try it here to be sure I'm doing it right.

Image
Failure is not an option
Joe C
New Member
 
Posts: 6
Joined: Tue Jan 30, 2018 8:37 pm


Return to SCCY CPX-1, CPX-2, & CPX-3 Accessories

Who is online

Users browsing this forum: No registered users and 1 guest

Join Florida Carry